1．Which statement about half-duplex Ethernet operations is ture?
A. With half-duplex transmission frames feed into a single cable in
one direction at a time.
B. half-duplex transmissino between stations is achieved by suing
point-to-point Ethernet and fast Ethernet connections.
C. Half-duplex transmission between stations is achieved by using
point-to-multipoint Ethernet and Fast Ethernet connections.
D. Half-duplex Ethernet technology provides a transmit circuit
connection wired directly to receiver circuit at the other end of
the connection.
Answer：A
B. point－to－point用于full－duplex，fast
Ethernet支持half－duplex也支持full－duplex。
C．怀疑错在point－to－multipoint上，书上我没有找到。
D．full－duplex的功能而不是half－duplex
2. which command should you use to configure a router so that it can
become a TFTP server host for a router system image that is run in
flash?
网管bitscn_com a. copy flash tftp
b. config tftp server
c. write network
d. tftp-server system
e. setup server tftp
Answer：D
命令出自Sybex P368
3．62.What are four functions/characteristics of the network layer of
the osi model?(choose four.)
*a. it uses a two-part address.
b.it maintains routing tables.
c. it uses broadcast addresses.
d.it establishes network addresses.
e. it provides access to the lan media.
f.it provides media independence for upper layers.
g.it provides path selection for internetwork communication.
Answer:ABCG
这道题的C和D有争议，认为C错的理由是broadcast address并不是layer3特有，layer2也用broadcast
address；认为D错的理由是establish这个用词有问题，大家自己看着办。
4．Which three statements about FR configurations using subinterfaces
are true?(Choose three.)
A.Each subinterface is configured either multipoint or point to
point
网管bitscn_com B.Any network address must be removed from the physical interface.
C.The configuration of sub interfaces is done in router
Config-(if)#mode. D.Frame relay encapsulation must be configured on
each sub interface.
Answer：ABC
D错，must这个词用得有问题。C可能是bible的笔误，router
Config-(if)#应该为router(Config-if)#
5. Question about PPP autentication. We have two cisco
routers-Router1 and Router2 (there are hostnames of the routers).
Router1 use username Router2 and password PasswordRouter1. How you
set the username and
password on Router2 for PPP autentication between Router1 and
Router2?
A. Username Router1 password PassRouter1
B. Username Router2 password Passrouter1
C. Username Router1 password PassRouter2
D. Username Router2 password Passrouter2
Answer:A
这个命令是：username 对方的名字password 相同的密码
6．Which command displays all routed protocols and the interface on
网管网www.bitscn.com which the protocol is enable?
A. Show protocols
B. Show protocols brief
C. Show interfaces protocol
D. Show interface
E. Show routed
F. Show routed interfaces
Answer：A
Sybex P275
7．(36).Which two statements about frame tagging are true? (Choose
two ) A .A filtering table is developed for each switch
B.Frame tagging assigns a unique user defined ID to each frame
C.A unique identifier is placed in the header of each frame as it is
forwarded between switches
D.Frame tagging is a technique that examines particular information
about each frame based on user defined offsets
Answer：BC
D．based on user defined offsets这里的表示有问题。
见Sybex P306
8.which two WAN data link layer protocols support multiple upper
layer protocols? (Chose two.)
A.PPP
B.LAPD
C.ISDN
D.HDLC
Answer：AD
Sybex P482
9．Which sequence of actions will allow telneting from a user’s PC to
中国网管论坛bbs.bitsCN.com a router using TCP/IP?
A. Connect the PC’s COM port to the router’s console port using a
straight-through cable.
B. Connect the PC’s COM port to the router’s console port using a
crossover cable.
C. Connect the PC’s COM port to the router’s Ethernet port using a
straight-through cable.
D. Connect the PC’s Ethernet port to the router’s Ethernet port
using a crossover cable.
E. Connect the PC’s Ethernet port to the router’s Ethernet port
using a rollover cable.
G. Connect the PC’s Ethernet port to the router’s Ethernet port
using a straight-through cable.
Answer: D
看仔细，这里用的是telnet，还有一道题是通过console。
telnet选D，如果是console则选B
When trying to determine the type of cable needed for a port, look
at the port and see if it is marked with an “X.” Use a
straight-through cable when only one port is designated with an “X.”
Use a crossover when both ports are designated with an “X” or when
网管u家u.bitsCN.com neither port has an “X.”（sybex P86）
10.Which line from a show spantree 1 command output indicates that
virtual lan 1 (vlan1 )is functioning properly?
a.root port is fast ethernet 0/26
b.port ethernet 0/1 of vlan1 is forwarding.
c.designated port is ethernet 0/1 ,path cost 10.
d.designated root has priority 0, address 00d0.588f.b600.
e. vlan1 is executing the ieee compatible spanning -tree protocol.
Answer：E
我觉得这道题应该有图，但没有在任何一份bible上看到图，因此答案我就不知道。E这句话正确，但不知道适不适用于这道题。
11．Which two statements about enabling the Novell IPX protocol on a
router are true?
A.NLSP supports primary and secondary network.
B.You can apply a maximum of one input filter and one output filter
per interface
C.You can configure multiple IPX networks on any supported interface
as long as each network uses a distinct encapsulation type.
D.A logical network on an interface is considered to be a secondary
网管联盟bitsCN_com
network as long as you include the keyword secondary in the command.
E.Because subinterfaces are logical entities of a physical
interface,any interface configuration paramenters that you
specify.on an individual subinterface are applied to all
subinterfaces for a given interface.
Answer：CD
A．NLSP是Netware Link Services
Protocol，它是一个高级的链路状态路由协议，是由Novell开发的，计划替代RIP和SAP。
B的错误是，可以设IPX列表，和SAP列表。同方向、同接口有两个。
12．Which WAN technology uses high-quality digital lines and IS
packet switched?
C.ATM
D.Frame Relay
Answer
FR是packet switched没有问题，sybex用的是high
performance。ATM在广域网上的性能肯定比FR要好，采用的是cell switched（特殊的packet
switched），ATM同时也用于局域网（LANE），因此ATM能不能叫WAN
technology也是一种疑问，同时ATM对NA并不要求。因此我偏向于选D。 同时有人以1000分通过考试，碰到这题也选D。
13．Which of the following is true concerning Frame Relay multipoint
中国网管联盟bitsCN.com
subinterfaces?
A. An IP address is required on the physical interface of the
central router.
B. All routers are required to be fully meshed.
C. All routers must be in the same subnet to forward routing updates
and broadcasts
D. Multipoint is the default configuration for Frame Relay
subinterfaces. Answer: C
B．如果只能用于fully meshed，那么就不用配置subinterface了。
D．在配置subinterface的时候，multipoint和point－to－point必须显示指出，他们都是不默认值（见人
评论加载中…
